View 74LVQ138SJ_662610.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

74LVQ138 Low Voltage 1-of-8 Decoder/Demultiplexer
May 1998
74LVQ138 Low Voltage 1-of-8 Decoder/Demultiplexer
General Description
The LVQ138 is a high-speed 1-of-8 decoder/demultiplexer. This device is ideally suited for high-speed bipolar memory chip select address decoding. The multiple input enables allow parallel expansion to a 1-of-24 decoder using just three LVQ138 devices or a 1-of-32 decoder using four LVQ138 devices and one inverter.
Features
n Ideal for low power/low noise 3.3V applications n Guaranteed simultaneous switching noise level and dynamic threshold performance n Improved latch-up immunity n Guaranteed incident wave switching into 75 n 4 kV minimum ESD immunity n Demultiplexing capability n Multiple input enable for each expansion n Active LOW mutually exclusive outputs
Ordering Code:
Order Number 74LVQ138SC 74LVQ138SJ Package Number M16A M16D Package Description 16-Lead (0.150" Wide) Small Outline Integrated Circuit, SOIC JEDEC 16-Lead Molded Small Outline Package, SOIC EIAJ
Devices also available in Tape and Reel. Specify by appending suffix letter "X" to the ordering code.
Logic Symbols
Connection Diagram
Pin Assignment for SOIC JEDEC and EIAJ
DS011350-1
IEEE/IEC
DS011350-2
Pin Descriptions
Pin Names A0-A2 E1-E2
DS011350-4
Description Address Inputs Enable Inputs Enable Input Outputs
E3 O0-O7
(c) 1998 Fairchild Semiconductor Corporation
DS011350
www.fairchildsemi.com
Functional Description
The LVQ138 high-speed 1-of-8 decoder/demultiplexer accepts three binary weighted inputs (A0, A1, A2) and, when enabled, provides eight mutually exclusive active-LOW outputs (O0-O7). The LVQ138 features three Enable inputs, two active-LOW (E1, E2) and one active-HIGH (E3). All outputs will be HIGH unless E1 and E2 are LOW and E3 is HIGH. This multiple enable function allows easy parallel expansion of the device to a 1-of-32 (5 lines to 32 lines) decoder with just four LVQ138 devices and one inverter (see Figure 1). The LVQ138 can be used as an 8-output demultiplexer by using one of the active LOW Enable inputs as the data input and the other Enable inputs as strobes. The Enable inputs which are not used must be permanently tied to their appropriate active-HIGH or active-LOW state.
Truth Table
Inputs E1 H X X L L L L L L L L E2 X H X L L L L L L L L E3 X X L H H H H H H H H A0 X X X L H L H L H L H A1 X X X L L H H L L H H A2 X X X L L L L H H H H O0 H H H L H H H H H H H O1 H H H H L H H H H H H O2 H H H H H L H H H H H Outputs O3 H H H H H H L H H H H O4 H H H H H H H L H H H O5 H H H H H H H H L H H O6 H H H H H H H H H L H O7 H H H H H H H H H H L
H = HIGH Voltage Level L = LOW Voltage Level X = Immaterial
Logic Diagram
DS011350-5
Please note that this diagram is provided only for the understanding of logic operations and should not be used to estimate propagation delays.
www.fairchildsemi.com
2
Logic Diagram
3
DS011350-6
FIGURE 1. Expansion to 1-of-32 Decoding
www.fairchildsemi.com
Absolute Maximum Ratings (Note 1)
Supply Voltage (VCC) DC Input Diode Current (IIK) VI = -0.5V VI = VCC + 0.5V DC Input Voltage (VI) DC Output Diode Current (IOK) VO = -0.5V VO = VCC + 0.5V DC Output Voltage (VO) DC Output Source or Sink Current (IO) DC VCC or Ground Current (ICC or IGND) Storage Temperature (TSTG) DC Latch-Up Source or Sink Current -0.5V to +7.0V -20 mA +20 mA -0.5V to VCC + 0.5V -20 mA +20 mA -0.5V to VCC + 0.5V
Recommended Operating Conditions (Note 2)
Supply Voltage (VCC) Input Voltage (VI) Output Voltage (VO) Operating Temperature (TA) Minimum Input Edge Rate (V/t) VIN from 0.8V to 2.0V VCC @ 3.0V 2.0V to 3.6V 0V to VCC 0V to VCC -40C to +85C
125 mV/ns
50 mA 200 mA -65C to +150C 300 mA
Note 1: The "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables are not guaranteed at the absolute maximum ratings. The "Recommended Operating Conditions" table will define the conditions for actual device operation. Note 2: Unused inputs must be held HIGH or LOW. They may not float.
DC Electrical Characteristics
Symbol Parameter VCC (V) 3.0 3.0 3.0 3.0 3.0 3.0 3.6 3.6 3.6 3.6 3.3 3.3 3.3 3.3 1.7 1.7 4.0 0.8 -0.8 2.0 0.8 0.002 TA = +25C Typ VIH VIL VOH Minimum High Level Input Voltage Maximum Low Level Input Voltage Minimum High Level Output Voltage 2.99 2.9 2.58 0.1 0.36 2.9 2.48 0.1 0.44 V V V V A mA mA A V V V V 1.5 0.8 0.8 V 1.5 2.0 TA = -40C to +85C Guaranteed Limits 2.0 V VOUT = 0.1V or VCC - 0.1V VOUT = 0.1V or VCC - 0.1V IOUT = -50 A VIN = VIL or VIH (Note 3) IOH = -12 mA VOL Maximum Low Level Outut Voltage IOUT = 50 A VIN = VIL or VIH (Note 3) IOL = 12 mA IIN IOLD IOH ICC VOLP VOLV VIHD VILD Maximum Input Leakage Current Minimum Dynamic (Note 4) Output Current Maximum Quiescent Supply Current Quiet Output Maximum Dynamic VOL Quiet Output Minimum Dynamic VOL Maximum High Level Dynamic Input Voltage Maximum Low Level Dynamic Input Voltage
Note 3: All outputs loaded; thresholds on input associated with output under test. Note 4: Maximum test duration 2.0 ms, one output loaded at a time. Note 5: Incident wave switching on transmission lines with impedances as low as 75 for commercial temperature range is guaranteed. Note 6: Worst case package. Note 7: Max number of outputs defined as (n). Data inputs are driven 0V to 3.3V; one output at GND. Note 8: Max number of Data Inputs (n) switching. (n - 1) inputs switching 0V to 3.3V. Input-under-test switching: 3.3V to threshold (VILD), 0V to threshold (VIHD), f = 1 MHz.
Units
Conditions
0.1
1.0
36 -25 40.0
VI = VCC, GND VOLD = 0.8V Max (Note 5) VOHD = 2.0V Min (Note 5) VIN = VCC or GND (Notes 6, 7) (Notes 6, 7) (Notes 6, 8) (Notes 6, 8)
www.fairchildsemi.com
4
AC Electrical Characteristics
Symbol Parameter VCC (V) Min tPLH tPHL tPLH tPHL tPLH tPHL tOSHL, tOSLH Propagation Delay An to On Propagation Delay An to On Propagation Delay E1 or E2 to On Propagation Delay E1 or E2 to On Propagation Delay E3 to On Propagation Delay E3 to On Output to Output Skew (Note 9) Data to Output 2.7 3.3 0.3 2.7 3.3 0.3 2.7 3.3 0.3 2.7 3.3 0.3 2.7 3.3 0.3 2.7 3.3 0.3 2.7 3.3 0.3 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 TA = +25C CL = 50 pF Typ 10.2 8.5 9.6 8.0 13.2 11.0 11.4 9.5 13.2 11.0 10.2 8.5 1.0 1.0 Max 18.3 13.0 17.6 12.5 21.0 15.0 19.0 13.5 21.8 15.5 18.3 13.0 1.5 1.5 TA = -40C to +85C CL = 50 pF Min 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 Max 21.0 15.0 20.0 14.0 23.0 16.0 21.0 15.0 23.5 16.5 20.0 14.0 1.5 1.5 ns ns ns ns ns ns ns Units
Note 9: Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate outputs of the same device. The specification applies to any outputs switching in the same direction, either HIGH to LOW (tOSHL) or LOW to HIGH (tOSLH). Parameter guaranteed by design.
Capacitance
Symbol CIN CPD (Note 10) Parameter Input Capacitance Power Dissipation Capacitance
Note 10: CPD is measured at 10 MHz.
Typ 4.5 45
Units pF pF
Conditions VCC = Open VCC = 3.3V
5
www.fairchildsemi.com
6
Physical Dimensions
inches (millimeters) unless otherwise noted
16-Lead (0.150" Wide) Small Outline Integrated Circuit Package Number M16A
7
www.fairchildsemi.com
74LVQ138 Low Voltage 1-of-8 Decoder/Demultiplexer
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
16-Lead Molded Small Outline Package Package Number M16D
LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support 1. Life support devices or systems are devices or sysdevice or system whose failure to perform can be reatems which, (a) are intended for surgical implant into sonably expected to cause the failure of the life support the body, or (b) support or sustain life, and (c) whose device or system, or to affect its safety or effectiveness. failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user.
Fairchild Semiconductor Corporation Americas Customer Response Center Tel: 1-888-522-5372 Fax: 972-910-8036 Fairchild Semiconductor Europe Fax: +49 (0) 1 80-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 8 141-35-0 English Tel: +44 (0) 1 793-85-68-56 Italy Tel: +39 (0) 2 57 5631 Fairchild Semiconductor Hong Kong Ltd. 8/F Room 808 Empire Centre 68 Mody Road, Tsimshatsui East Kowloon, Hong Kong Tel: 852-2722-8338 Fax: 852-2722-8383 Fairchild Semiconductor Japan Ltd. 4F, Natsume BI, 2-18-6 Yushima, Bunkyo-ku, Tokyo 113-0034, Japan Tel: 81-3-3818-8840 Fax: 81-3-3818-8450
www.fairchildsemi.com
Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications.

▲Up To Search▲

Price & Availability of 74LVQ138SJ

	To Download 74LVQ138SJ Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .